聚醚醚酮,PEEK TECAPEEK® PVX东莞市双帮塑胶原料有限公司常年销售的塑料,因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告,COA原料出厂报告,REACH报告,SVHC报告,UL黄卡,提供原料注塑加工工程中可能出现的各种异常现象解决方法,塑料牌号太多,本网站没有提供的本公司也有代理,详情请咨询本公司相关业务人员0769-87795123
13549213581 肖生
TECAPEEK® PVX
Polyetheretherketone
Ensinger Inc.
Technical Data
Product Description
TECAPEEK® PVX is an ultra high performance bearing material that incorporates the properties of a premium polymetric matrix material with optimum levels of specific wear enhancing additives. This formulation raises the continuous use temperature by approximately 40°F and increases the limiting PV while maintaining excellent chemical resistance. When used as a non-metallic bearing, TECAPEEK® PVX offers a superb range of tribiological performance. It is designed to run at high loads and speeds, in hostile environments, either dry or lubricated.
TECAPEEK™ PVX'S exceptional properties make it an ideal material for bearing surfaces in the most demanding applications and in the harshest conditions. Industrial, automotive, marine, nuclear, petroleum and aerospace industry applications realize great benefits from its use.
General
Material Status • Commercial: Active
Literature 1 • Technical Datasheet (English)
Availability • North America
Additive • Unspecified Additive
Features • Good Chemical Resistance • Good Weather Resistance • Low Smoke Emission
• Good Wear Resistance • High Heat Resistance • Radiation (Gamma) Resistant
Uses • Aerospace Applications • Industrial Applications • Nuclear Power Applications
• Automotive Applications • Marine Applications • Oil/Gas Applications
Forms • Plate • Rod
Physical Nominal Value (English) Nominal Value (SI) Test Method
Specific Gravity 1.48 1.48 g/cm³ ASTM D792
Mechanical Nominal Value (English) Nominal Value (SI) Test Method
Tensile Strength (Yield, 73°F (23°C)) 17300 psi 119 MPa ASTM D638
Tensile Elongation (Break, 73°F (23°C)) 2.5 % 2.5 % ASTM D638
Flexural Modulus - Tangent (73°F (23°C)) 1.40E+6 psi 9650 MPa ASTM D790
Flexural Strength (73°F (23°C)) 30000 psi 207 MPa ASTM D790
Compressive Strength (73°F (23°C)) 22000 psi 152 MPa ASTM D695
Coefficient of Friction 3 0.19 to 0.21 0.19 to 0.21 ASTM D1894
Wear Rate 0.00125 to 0.00150 in/min 0.00125 to 0.00150 in/min
Impact Nominal Value (English) Nominal Value (SI) Test Method
Notched Izod Impact (73°F (23°C)) 3.3 ft•lb/in 170 J/m ASTM D256
Hardness Nominal Value (English) Nominal Value (SI) Test Method
Rockwell Hardness (M-Scale) 85 85 ASTM D785
Thermal Nominal Value (English) Nominal Value (SI) Test Method
Deflection Temperature Under Load ASTM D648
264 psi (1.8 MPa), Unannealed, 0.250 in (6.35 530 °F 277 °C
mm)
Continuous Use Temperature 500 °F 260 °C
Melting Temperature 633 °F 334 °C
CLTE - Flow 3.1E-6 in/in/°F 5.6E-6 cm/cm/°C ASTM D696
Electrical Nominal Value (English) Nominal Value (SI) Test Method
Surface Resistivity 1.0E+5 to 1.0E+8 ohms 1.0E+5 to 1.0E+8 ohms ASTM D257
Volume Resistivity (73°F (23°C)) 1.4E+5 ohms•cm 1.4E+5 ohms•cm ASTM D257
Flammability Nominal Value (English) Nominal Value (SI) Test Method
Flame Rating V-0 V-0 UL 94
Additional Information Nominal Value (English) Nominal Value (SI)
Limiting Pressure Velocity 25000 to 30000 25000 to 30000
Data based on injection molded samples.
聚醚醚酮,PEEK TECAPEEK® PVX是东莞市双帮塑胶原料有限公司常年销售的塑料,因为塑料价格行情每天都有新变化前天的报价不等于今天的报价。本公司销售的所有原料保证是原厂原包,随料可以提供生产厂商提供的物性表、SGS报告,COA原料出厂报告,REACH报告,SVHC报告,UL黄卡,提供原料注塑加工工程中可能出现的各种异常现象解决方法,塑料牌号太多,本网站没有提供的本公司也有代理,详情请咨询本公司相关业务人员0769-87795123
13549213581 肖生
|